Playbar

Home theater soundbar and streaming music speaker in one—

Note:The grille cloth is not removable. Tampering with the cloth may damage your Playbar.

 

Controls and lights

volume_up.jpgvolume_down.jpg 

Volume up (+)

Volume down (-)

Press to adjust the volume.

Note:You can also use the app and remote control.

ALL_play_pause.jpg 

Play/Pause

  • Press once to play or pause music.

  • Press twice to skip to the next song (if applicable to the selected music source).

  • Press three times to go back to the previous song.

  • Press and hold to add the music playing in another room.

Note:You can’t skip forward or go back when listening to a radio station.

 

Status light

Indicates the status. For more information, see https://faq.sonos.com/led.

 

IR sensor light

The IR (InfraRed) sensor receives signals sent by a remote control.

When the Playbar receives a volume or mute command, the IR light displays momentarily.

You can adjust this setting so the light never displays.

Go to ALL_more_sm.jpg > Settings > Room Settings and choose the room the Playbar is in. Select Remote > IR Signal Light.

Connector panel

ALL_PB_back_zoominNEW.jpg

Ethernet ports (2)

Use the supplied Ethernet cable if you want to connect to a router, computer, or network-attached storage (NAS) device (optional).

Digital audio IN (optical)

Use an audio optical cable to connect the Playbar to your TV.

ALL_opticalplugerror_guide.jpg

AC power (mains) input

Use only the supplied power cord (using a third-party power cord will void your warranty).

Note:Insert the power cord firmly until it is flush with the speaker.

ALL_PB_powerplug.jpg

IR repeater

Allows the commands from your remote control to reach your TV if the Playbar is positioned in front of the TV.

 

This setting is on by default, but can be turned off.

Go to ALL_more_sm00097.jpg > Settings > Room Settings and choose the room the Playbar is in. Select Remote > IR Repeater.

Select a location

You can mount the Playbar to a wall above or below your TV or place it on a credenza.

Placed on a credenza

Wall mounted

To put Playbar on a wall, see Wall mounting.

Connect the cables

Before you start

  1. Disconnect existing home theater or surround sound equipment from your TV.

  2. Connect any external devices, like a cable box or DVD player, directly to your TV.

Connect the soundbar to your TV

  1. Remove the protective cap from each end of the optical audio cable.

  2. Connect the optical audio cable from your TV’s digital audio OUT (optical) to the Playbar’s digital audio IN (optical). Don’t twist or bend the cable.

Note:The Playbar’s digital audio IN port and the optical cable are ‘D-shaped’—make sure the connector aligns correctly into the port.

ALL_PB_opticalcable.jpg

 

Connect the power cord

Attach the power cord and plug in the Playbar. Push the power cord in firmly until it is flush with the surface. 

ALL_PB_powerplug00101.jpg

If you don’t have the app, download it from the app store. You’ll use it to set up and control your Sonos system. See Getting started.

Wall mounting

You can mount Playbar to a wall above or below a wall-mounted TV. Use the Playbar wall mount kit. You can buy it on www.sonos.com. Follow the instructions in the kit.

Caution:Don’t use any other hardware to mount the Playbar.

Guidelines

Note:Connect the power and audio cables to the Playbar before mounting to the wall.

What you need

Note:There are 2 spare screws (and anchors) included in the kit. Use these to provide additional reinforcement if you’d like.

  1. Tape the template to the wall above or below your TV. Use a level.

    ALL_PB_wallmount1.jpg
  2.  

  3. Use a pointed tool to pierce through the template and mark the mounting holes. Mark closer to the corners of the holes.

    ALL_PB_wallmount2.jpg
  4. Remove the template.

  5. Drill pilot holes.

  6. Wall mounting information

    Wall Material

    Pre Drill

    Use Wall Anchors

    Use Screws

    Wood Stud

    1/8" (3mm) bit

    No

    Yes

    Drywall (no stud)

    3/16" (4.5mm) bit

    Yes

    Yes

    Hard wallboard or double board

    3/16" (4.5mm) bit

    Yes

    Yes

    Plaster

    1/4" (6.5mm) bit

    Yes

    Yes

    Concrete or Brick

    1/8" (3mm) bit

    Yes

    Yes

     

  7. Insert and secure the wall anchors (don’t use the anchors if drilling into wood).

  8. ALL_PB_wallmount3.jpg

     

  9. Place the bracket on the wall and loosely tighten the screws to secure the bracket. Check with a level and then tighten the screws.

  10. Hang the Playbar securely on the bracket pegs.

    ALL_PB_wallmount4.jpg

Specifications

Feature

Description

Audio

Amplifier

Nine Class-D digital amplifiers perfectly tuned to match the nine dedicated speaker drivers and the acoustic architecture.

Tweeter

Three tweeters create the crispest and clearest high-frequency response.

Mid-Woofer

Six mid-woofers give you the full range of sound effects and music from the left and right channels, and crisp, clear dialog from the center. Mid-woofers act together as a phased speaker array so what you hear matches what you see on screen.

System Requirements

TV with optical audio output, broadband Internet, and a Sonos app. Internet-connected TV not required.

Networking*

Wireless Connectivity

Connects to your home Wi-Fi network with any 802.11b/g/n router.

802.11n only network configurations are not supported—you can either change the router settings to 802.11b/g/n or connect a Sonos product to your router.

Ethernet Port (2)

Two 10/100 Mbps Ethernet ports. You can plug a Sonos product directly into your router if your Wi-Fi is unstable.

General

Power Supply

Auto-switching 100-240 V, 50-60 Hz 2A AC universal input.

Dimensions (H x W x D)

3.35" (H) x 35.43" (W) x 5.51" (D), 85mm (H) x 900mm (W) x 140 mm (D)

Weight

11.9 lb (5.4 kg)

Operating Temperature

32°F to 104°F (0°C to 40°C)

Storage Temperature

-4°F to 158°F (-20°C to 70°C)

Multiple Orientations

Mount Playbar on the wall either above or below your TV, or lay flat on your TV table.

Control

Use your remote control, voice, touch controls or the Sonos app.

Supported Devices

Playbar connects to your TV using a single optical cable and plays all sources connected to the TV, including cable boxes and game consoles.

Package Contents

Playbar, AC power cord, optical audio cable, Quickstart Guide, and legal booklet.

 

* Specifications subject to change without notice.