Accessories

Find the perfect accessory for your Sonos system—tailored to perfectly fit your Sonos products.

For the full selection of Sonos-compatible stands, wall mounts, and cables, see Accessories on our website.

Sonos Stand

A set of custom-designed stands for Sonos One and Play:1 provide an elegant solution for placing your home theater surrounds.

What’s in the box?

The kit contains a pair of Sonos stands. Each stand assembly includes:

Note:Sonos speakers sold separately.

What you’ll need

Assembling your Sonos Stand

  1. Take everything out of the box and place the base in the packaging slot to stabilize it for the next few steps. Unplug your Sonos speaker, and thread the speaker end of the power cord through the opening in the base.

    _1_Stand_BaseInBox.jpg
  2.  

  3. Insert the stem snugly into the base, using the alignment pins to position the power cord channel either in the front or back. Use the 2 black screws and a Phillips-head screwdriver to attach the base.

    _2Stand_BaseAssy.jpg
  4.  

  5. Route the speaker’s power cord through the speaker platform.

    _3_Stand_SpeakerPlatform.jpg

  6.  

     

  7. Use the 2 silver screws to attach the speaker platform to the top of the stem, threading the power cable carefully. Snap the bottom plate on with the power cable channel in the back, and mount the platform on the stem.

    _4_Stand_SpeakerPlatform_wBottom.jpg

  8. Plug the power cord back into the speaker and place on the top mount, pulling any extra cable down from the top. Tighten the screws and attach the top cap with the notch facing toward the speaker.

    _5_Stand_CapPole.jpg
  9.  

  10. Press the power cord into the stem, working from top to bottom. Pull the excess cable down from the base.

    _6_Stand_PressInCord.jpg
  11.  

  12. Tilt the stand forward slightly to wrap the excess cord around the bottom of the base. Plug the speaker’s power cable into the wall and enjoy the music!

    _7_Stand_PwrCordManagement.jpg

Sonos Shelf

The easy-to-install shelf for Sonos One and Play:1 securely holds your speaker in place—its space-saving design provides a designated space for your speaker.

What’s in the box?

Note:Sonos speakers sold separately.

What you’ll need

Assembling your Sonos Shelf

  1. Place the wall bracket against the wall and mark the screw holes. (Make sure the black bracket foam ring is face up.)

    _1_Shelf_FINAL.jpg

  2.  

  3. If using wall anchors, use a 5/16" drill bit to drill 2 pilot holes and then insert the wall anchors. Refer to the wall mounting information below for guidelines. Otherwise skip this step.

    _2_Shelf_FINAL.jpg

  4. WALL MATERIAL

    PRE-DRILL

    USE WALL ANCHORS

    USE SCREWS

    Wood stud

    1/8” / 3mm bit

    No

    Yes

    Drywall (no stud)

    5/16” / 8mm bit

    Yes

    Yes

    Hard wallboard or double board

    5/16” / 8mm bit

    Yes

    Yes

    Plaster

    5/16” / 8mm bit

    Yes

    Yes

    Concrete or Brick

    5/16” / 8mm bit

    Yes

    Yes

     

     

  5. Use a Phillips-head screwdriver or a power drill to screw the bracket to the wall.

    _3_Shelf_FINAL.jpg

  6.  

  7. Position the shelf the way you want it (supports left or right speaker placement). Press the shelf firmly on to the wall bracket until it snaps into place (both front and back).

  8. _4_Shelf_FINAL.jpg

     

     

  9. Route the speaker’s power cord through the shelf opening. (You’ll wrap the cord around the bottom of the shelf after it’s assembled.)

    _5_Shelf_FINAL.jpg

  10.  

     

  11. Press the bottom cover firmly onto the shelf until it snaps into place, carefully aligning the pins. Plug the power cord into the speaker and place the speaker on top of the shelf.

    _6_Shelf_FINAL.jpg

  12.  

  13. Wrap the excess power cord around the bottom of the shelf.

    _7_Shelf_FINAL.jpg

  14.  

  15. Your shelf assembly is complete—time to play some music!

_8_Shelf_FINAL.jpg

 

Wall Mount for Beam

See Wall mount for more information

Wall Mount for Playbar

See Wall mount for more information

Sonos Architectural by Sonance speakers

Sonos Architectural by Sonance speakers include exclusively-designed audio enhancements when used with a Sonos Amp. These enhancements include:

To unlock Sonos audio enhancements

After you install your Sonos Architectural speakers and set up Amp, go to the settings for the room associated with these speakers and select Detect Sonos Architectural.

Other accessories

For a full selection of wall mounts, stands, and cables, tailored to perfectly fit your Sonos products, see Accessories on our website.