Wall mount


Mount kit contents

Note:Don’t discard the template. It may look like packing material.




  1. Tape the cardboard template to the wall above or below your TV. Use a level. Keep 1" (25mm) space (minimum) for access to Beam’s touch controls. (Don’t install Beam vertically.)

  2. Mark the center of the mounting holes and remove the template.

  3. ELRey_wall_mount_Step2.jpg


  4. Use a 5/16" drill bit to drill pilot holes (see Wall mounting information)

  5. wall_mount_Step3.jpg


  6. Insert and secure the wall anchors (don’t use the anchors if drilling into wood).

  7. ELRey_wall_mount_Step4.jpg


  8. Place the bracket on the wall and loosely tighten the wall screws to secure the bracket. Check with a level and then tighten the screws.

  9. ELRey_wall_mount_Step5.jpg


  10. Connect the power and HDMI cables to Beam.

  11. ELRey_wall_mount_Step6.jpg


  12. Place Beam on the bracket.

  13. ELRey_wall_mount_Step7.jpg


  14. Insert and tighten Beam to the bracket using the mounting screws.



Wall mounting information

Wall Material

Pre Drill

Use Wall Anchors

Use Screws

Wood Stud

1/8" / 3 mm bit



Drywall (no stud)

5/16" / 8 mm bit



Hard wallboard or double board

5/16" / 8 mm bit




5/16" / 8 mm bit

No, requires toggle bolt


Concrete or Brick

5/16" / 8 mm bit








Five Class-D digital amplifiers.

Elliptical Woofer

Four full-range woofers ensures you’ll hear the faithful playback of mid-range vocal frequencies plus deep, rich bass.


One tweeter creates a crisp and clear high-frequency response.


  • Five far-field microphone array uses for advanced beam forming and multichannel echo cancellation.

  • LED hard-wired to voice microphones for privacy control so you know when the microphone is active.

Voice Control

Integrated voice control.

System Requirements

TV with HDMI ARC or optical digital audio output, broadband internet, and the Sonos app.


Wireless Connectivity

Using Sonos S2: Connects to WiFi network with any 802.11 b/g/n, 2.4 GHz broadcast-capable router.

Using Sonos S1: Connects to WiFi network with any 802.11b/g 2.4  GHz broadcast-capable router. 802.11n only network configurations are not supported—you can either change the router settings to 802.11b/g/n or connect a Sonos product to your router.

Ethernet Port

One 10/100 Mbps Ethernet port. You can plug a Sonos product directly into your router if your WiFi is unstable.


Power Supply

Auto-switching 100-240 V, 50-60 Hz 2.5A AC universal input.

Dimensions (H x W x D)

2.68 x 25.63 x 3.94 in. (68 x 651 x 100 mm)


6.2 lb (2.8 kg)

Operating Temperature

32°F to 104° F (0° C to 40° C)

Storage Temperature

-4°F to 122° F (-20° C to 50° C)


Use your remote control, voice, touch controls or the Sonos app.

Supported Devices

Connects to TV with HDMI cable (with or without an attached optical adapter). Plays sources connected to the TV, including cable boxes and game consoles.

Package Contents

Beam, AC power cord, HDMI cable, optical adapter, Quickstart Guide.

* Specifications subject to change without notice.

Important Safety Information

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.If your product is wallmounted:

  • Improper or inadequate wallmount installation could cause your device to fall, resulting in personal injury.

  • Never hang from the Sonos product or the wall bracket.

  • Once wall-mounted, periodically check to ensure screws remain securely tightened.

6.Do not use this apparatus near water.

7.Clean only with dry soft cloth. Household cleaners or solvents can damage the finish on your Sonos components.

8.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

9.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus that produce heat.

10.Protect the power cable from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachments/accessories specified by the manufacturer.

12.Unplug this apparatus during lightning storms or when unused for long periods of time.

13.Refer all servicing to Sonos qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cable or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

14.The Mains plug should be readily available to disconnect the equipment.

15.Warning.pngWarning: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

16.Do not expose apparatus to dripping or splashing and do not place objects filled with liquids, such as vases, on the apparatus.